Skip to content

How to Remove Broken Bleeder Screw

  • by

Assuming you are talking about a bleeder screw on a car, the process is actually quite simple. First, locate the affected bleeder screw and identify what type it is. There are two common types of bleeder screws- those with an internal hexagon (hex) or those with an external hexagon (EH).

If the broken bleeder screw is an internal hex type, then you will need to use a pair of pliers to grip the exposed part of the screw.

  • Remove the tire and wheel assembly
  • Unscrew the bleeder screw using a flathead screwdriver or Allen wrench
  • Apply pressure to the brake pedal to push out any air bubbles
  • Screw in a new bleeder screw and tighten it until it is snug
  • Reattach the tire and wheel assembly

Broken Brake Bleeder Screw Removal

What Do You Do If a Bleeder Screw Breaks?

If a bleeder screw breaks, the first thing you should do is try to remove the broken screw. If the screw is stuck, you may need to use a drill or other tool to remove it. Once the screw is removed, you can then attempt to repair the hole using a patch kit or by drilling a new hole.

If you are unable to repair the hole, you may need to replace the entire brake line.

Can You Heat a Brake Bleeder Screw?

You can heat a brake bleeder screw to loosen it, but be careful not to overheat the surrounding area as this can damage the ABS system. Use a low setting on your heat gun and apply heat evenly around the base of the screw. You may need to repeat this process a few times before the screw becomes loose enough to turn.

Is the Bleeder Screw a Hollow Screw?

Yes, the bleeder screw is a hollow screw. This allows for the easy passage of fluid through the screw and into the surrounding area. The hollow nature of the screw also allows for air to escape from the system, which is necessary in order to bleed the brakes correctly.



Broken Brake Bleeder Removal Tool

Assuming you are referring to a broken brake bleeder removal tool, this would refer to a tool that is used to remove the brake bleeder screw from the brake caliper. This can happen if the screw is over-tightened or if it becomes corroded. To remove a broken brake bleeder removal tool, you will need a few tools including a drill, a small punch, and a hammer.

You will also need some patience as this process can be time-consuming. First, you will need to locate the broken piece of the tool. Once you have found it, you will need to use the drill to create a hole in the center of it.

Next, take the small punch and place it into the hole that you just created. Finally, use the hammer to tap on the punch until the broken piece comes loose from the caliper.

Can I Drive With a Broken Bleeder Valve

If you have a broken bleeder valve, you may be able to drive your car for a short period of time. However, it is not advisable to do so. A broken bleeder valve can cause your brakes to fail, which could lead to an accident.

If you must drive with a broken bleeder valve, be sure to go slowly and keep your eyes on the road at all times.

Bleeder Screw Repair Kit

If your car has manual brakes, there\’s a good chance it has bleeder screws. These screws are used to bleeding the brakes – in other words, they help get rid of air bubbles in the brake fluid. Over time, however, these screws can become damaged or even break off.

When this happens, you\’ll need a bleeder screw repair kit. This kit usually includes new bleeder screws and seals. It might also come with a tool to help remove the old screws.

Installing the new parts is relatively easy – just follow the instructions that come with the kit. Once you\’re done, your brakes should be back to working like new!


Removing a broken bleeder screw can be difficult, but there are a few methods you can try. One is to use a pair of needle-nose pliers to grab the end of the screw and twist it out. Another is to use a drill to make a hole in the center of the screw so you can grip it with pliers and twist it out.

If neither of these methods work, you may need to remove the entire brake caliper and replace the bleeder screw.